Z01 Standard 1A Triacs Features A2 ■ On-state rms current, I 1 A T(RMS) ■ Repetitive peak off-state voltage, VDRM/VRRM G 600 or 800 V A1 ■ Triggering gate current, I 3 to 25 mA A2 GT (Q1) Description G A2 The Z01 series is suitable for general purpose AC A2 switching applications. These devices are A1 G A1 typically used in applications such as home TO-92 SOT-223 appliances (electrovalve, pump, door lock, small Z01xxA Z01xxN lamp control), fan speed controllers,... Different gate current sensitivities are available, A2 allowing optimized performance when driven directly through microcontrollers. A1 G SMBflat-3L Z01xxMUF December 2010 Doc ID 7474 Rev 10 1/12 www.st.com 12

Characteristics Z01 1 Characteristics T able 1. Absolute maximum ratings Symbol Parameter Value Unit SOT-223 T = 90 °C tab On-state rms current I TO-92 T = 50 °C 1 A T(RMS) (full sine wave) L SMBflat-3L T = 107 °C tab Non repetitive surge peak on-state F = 50 Hz t = 20 ms 8 I A TSM current (full cycle, Tj initial = 25 °C) F = 60 Hz t = 16.7 ms 8.5 I²t I²t Value for fusing t = 10 ms 0.35 A²s p Critical rate of rise of on-state current dI/dt F = 120 Hz T = 125 °C 20 A/µs I = 2 x I , t ≤ 100 ns j G GT r I Peak gate current t = 20 µs T = 125 °C 1 A GM p j P Average gate power dissipation T = 125 °C 1 W G(AV) j T Storage junction temperature range - 40 to + 150 stg °C T Operating junction temperature range - 40 to + 125 j T able 2. Electrical characteristics (T = 25 °C, unless otherwise specified) j Z01 Symbol Test conditions Quadrant Unit 03 07 09 10 I - II - III 3 5 10 25 IGT (1) VD = 12 V, IV MAX. 5 7 10 25 mA R = 30 Ω L V ALL MAX. 1.3 V GT V = V , D DRM V R = 3.3 kΩ, ALL MIN. 0.2 V GD L T = 125 °C j I (2) I = 50 mA MAX. 7 10 10 25 mA H T I - III - IV 7 10 15 25 I I = 1.2 I MAX. mA L G GT II 15 20 25 50 V = 67% V gate open dV/dt(2) D DRM MIN. 10 20 50 100 V/µs T = 110 °C j (dV/dt) (dI/dt) = 0.44 A/ms, c c MIN. 0.5 1 2 5 V/µs (2) T = 110 °C j 1. Minimum I is guaranteed at 5% of I max. GT GT 2. For both polarities of A2 referenced to A1. 2/12 Doc ID 7474 Rev 10

Z01 Characteristics T able 3. Static characteristics Symbol Test conditions Value Unit V (1) I = 1.4 A, t = 380 µs T = 25 °C MAX. 1.6 V TM TM p j V (1) Threshold voltage T = 125 °C MAX. 0.95 V to j R (1) Dynamic resistance T = 125 °C MAX. 400 mΩ d j IDRM V = V Tj = 25 °C MAX. 5 µA IRRM DRM RRM Tj = 125 °C 0.5 mA 1. For both polarities of A2 referenced to A1. Table 4. T hermal resistances Symbol Parameter Value Unit R Junction to tab (AC) SOT-223 25 th(j-t) R Junction to tab (AC) SMBflat-3L 14 th(j-t) R Junction to lead (AC) TO-92 60 th(j-I) MAX. °C/W SOT-223 60 S(1) = 5 cm² R Junction to ambient SMBflat-3L 75 th(j-a) TO-92 150 1. S = copper surface under tab. Figure 1. Maximum power dissipation Figure 2. On-state rms current versus lead versus on-state rms current (TO-92) or tab (SOT-223, SMBflat- (full cycle) 3L) temperature (full cycle) P(W) IT(RMS)(A) 1.50 1.2 α=180° 1.25 1.0 SMBF3L 1.00 0.8 SOT-223 0.75 0.6 TO-92 0.50 0.4 0.25 180° 0.2 IT(RMS)(A) TlorTtab(°C) 0.00 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 25 50 75 100 125 Doc ID 7474 Rev 10 3/12

Characteristics Z01 Figure 3. O n-state rms current versus Figure 4. Relative variation of thermal ambient temperature (free air impedance versus pulse duration convection full cycle) (Z ) th(j-a) IT(RMS)(A) 1.2 K=[Zth(j-a)/Rth(j-a)] 1.00 Z01xxA 1.0 Rth(j-a)= 60°C/W Z01xxMUF (SOT-223) Copper surface area = 5cm² 0.8 Rth(j-a)= 100°C/W (SMBflat-3L) 0.6 0.10 Z01xxN 0.4 Rth(j-a)= 150°C/W (TO-92) 0.2 tp(s) Tamb(°C) 0.01 0.0 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 0 25 50 75 100 125 Figure 5. R elative variation of holding Figure 6. Relative variation of gate trigger current and latching current versus current (I ) and voltage (V ) GT GT junction temperature (typ. values) versus junction temperature IH,IL[Tj] /IH,IL[Tj=25°C] 3.0 IGT,VGT[Tj]/IGT,VGT[Tj=25°C] 2.5 2.5 2.0 IGTQ1-Q2 2.0 IGTQ3 1.5 IGTQ4 1.5 1.0 IL 1.0 VGTQ1-Q2-Q3-Q4 0.5 Tj(°C) IH 0.5 0.0 0.0 Tj(°C) -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 Figure 7. S urge peak on-state current versus Figure 8. Non-repetitive surge peak number of cycles on-state current and corresponding value of I2t sinusoidal pulse width I (A) 9 TSM ITSM(A),I2t (A2s) 100.0 8 Tjinitial = 25°C 7 T = 20 ms dI/dt limitation: 6 Non repetitive One cycle 20A/µs ITSM Tjinitial = 25 °C 10.0 5 4 3 1.0 2 Repetitive I2t 1 Tamb= 95 °C Number of cycles tp(ms) 0 0.1 1 10 100 1000 0.01 0.10 1.00 10.00 4/12 Doc ID 7474 Rev 10

Z01 Characteristics Figure 9. O n-state characteristics Figure 10. Relative variation of critical rate (maximum values) (I = f(V ) of decrease of main current versus TM TM (dV/dt) c ITM(A) (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 10.0 2.6 2.4 2.2 2.0 1.8 1.6 Tj=Tjmax. 1.4 1.0 1.2 1.0 Tj=max. 0.8 Tj= 25°C RVdt=0=400.09 5mVΩ 0.6 Z0103 Z0109 0.4 Z0107 Z0110 VTM(V) 0.2 (dV/dt)c (V/µs) 0.1 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.1 1.0 10.0 100.0 Figure 11. R elative variation of critical rate of Figure 12. SOT-223 and SMBflat-3L thermal decrease of main current (dI/dt) resistance junction to ambient versus junction temperature versus copper surface under case R (°C/W) th(j-a) (dI/dt)c [Tj] /(dI/dt)c [TjSpecified] 170 6 160 150 5 140 130 4 120 3 110 SMBF3L 100 2 90 80 SOT223 1 70 Tj(°C) 0 60 S (cm²) 0 25 50 75 100 125 50 CU 0 1 2 3 4 5 Figure 13. Relative variation of static dV/dt immunity versus junction temperature (gate open) 6 dV/dt[Tj]/dV/dt[Tj=125°C] VD=VR=402V 5 4 3 2 1 0 Tj(°C) 25 50 75 100 125 Doc ID 7474 Rev 10 5/12

Ordering information scheme Z01 2 Ordering information scheme Figure 14. Ordering information scheme Z 01 03 M A [BLANK] 1AA2 Triac series Current 01 = 1 A Sensitivity 03 = 3 mA 07 = 5 mA 09 = 10 mA 10 = 25 mA Voltage M = 600 V N = 800 V Package A =TO-92 N = SOT-223 UF = SMBF3L Packing mode 1AA2 =TO-92 bulk 2AL2 =TO-92 ammopack 5AL2 =TO-92 tape and reel 5AA4 = SOT-223 tape and reel7” 6AA4 = SOT-223 tape and reel 13” Blank = SMBflat-3L tape and reel 13” 6/12 Doc ID 7474 Rev 10

Z01 Ordering information scheme T able 5. Product Selector Voltage Order code Sensitivity Type Package 600 V 800 V Z0103MA X 3 mA Standard TO-92 Z0103MN X 3 mA Standard SOT-223 Z0103NA X 3 mA Standard TO-92 Z0103NN X 3 mA Standard SOT-223 Z0107MA X 5 mA Standard TO-92 Z0107MN X 5 mA Standard SOT-223 Z0107NA X 5 mA Standard TO-92 Z0107NN X 5 mA Standard SOT-223 Z0109MA X 10 mA Standard TO-92 Z0109MN X 10 mA Standard SOT-223 Z0109NA X 10 mA Standard TO-92 Z0109NN X 10 mA Standard SOT-223 Z0110MA X 25 mA Standard TO-92 Z0110MN X 25 mA Standard SOT-223 Z0110NA X 25 mA Standard TO-92 Z0110NN X 25 mA Standard SOT-223 Z0103MUF X 3 mA Standard SMBflat-3L Z0107MUF X 5 mA Standard SMBflat-3L Z0109MUF X 10 mA Standard SMBflat-3L Doc ID 7474 Rev 10 7/12

Packaging information Z01 3 Packaging information ● Epoxy meets UL94, V0 ● Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. T able 6. SOT-223 dimensions Dimensions Ref. Millimeters Inches A V c Min. Typ. Max. Min. Typ. Max. A1 B A 1.80 0.071 e1 A1 0.02 0.10 0.001 0.004 D B 0.60 0.70 0.85 0.024 0.027 0.033 B1 B1 2.90 3.00 3.15 0.114 0.118 0.124 c 0.24 0.26 0.35 0.009 0.010 0.014 4 H E D(1) 6.30 6.50 6.70 0.248 0.256 0.264 1 2 3 e 2.3 0.090 e1 4.6 0.181 e E(1) 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 V 10° max 1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches) Figure 15. SOT-223 footprint dimensions (in millimeters) 3.25 1.32 5.16 7.80 1.32 2.30 0.95 8/12 Doc ID 7474 Rev 10

Z01 Packaging information T able 7. TO-92 dimensions Dimensions REF. Millimeters Inches Min. Typ. Max. Min. Typ. Max. A A 1.35 0.053 a B 4.70 0.185 B C C 2.54 0.100 F D E D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 T able 8. SMBflat-3L dimensions Dimensions Ref. Millimeters Inches Min. Typ. Max. Min. Typ. Max. A 0.90 1.10 0.035 0.043 A c b 0.35 0.65 0.014 0.026 e D b 2x b4 1.95 2.20 0.07 0.087 L 2x L2 2x c 0.15 0.40 0.006 0.016 L1 E E1 D 3.30 3.95 0.130 0.156 L1 E 5.10 5.60 0.201 0.220 L L2 E1 4.05 4.60 0.156 0.181 b4 L 0.75 1.50 0.030 0.059 L1 0.40 0.016 L2 0.60 0.024 e 1.60 0.063 Figure 16. SMBflat-3L footprint dimensions 5.84 0.51 (0.230) (0.020) 2.07 2.07 (0.082) (0.082) 0.51 (0.020) 1.20 3.44 1.20 (0.047) (0.136) (0.047) millimeters (inches) Doc ID 7474 Rev 10 9/12

Packaging information Z01 Figure 17. Footprint and connectors for SOT-223 or SMBflat-3L (dimensions in mm) 5.84 3.42 3.25 2.92 50 32 19 SOT-223 1. 1. 1. Solder resist 1.35 1.30 1.20 1.20 1.08 1.08 0.610.510.46 SMBF3L Solder lands 2.07 SMBF3L 1.95 2.07 2.22 7.80 SMBF3L Solder paste Connector line 729 431 SOT-223 SOT-223 SOT-223 1.1.1. 0.85 0.95 1.10 2.30 10/12 Doc ID 7474 Rev 10

Z01 Ordering information 4 Ordering information T able 9. Ordering information Order code(1) Marking(1) Package Weight Base quantity Delivery mode Z01xxyA 1AA2 Z01xxyA TO-92 0.2 g 2500 Bulk Z01xxyA 2AL2 Z01xxyA TO-92 0.2 g 2000 Ammopack Z01xxyA 5AL2 Z01xxyA TO-92 0.2 g 2000 Tape and reel Z0103yN 5AA4 Z3y SOT-223 0.12 g 1000 Tape and reel Z0107yN 5AA4 Z7y SOT-223 0.12 g 1000 Tape and reel Z0109yN 5AA4 Z9y SOT-223 0.12 g 1000 Tape and reel Z0103MUF Z3M SMBflat-3L 46.78 mg 5000 Tape and reel Z0107MUF Z7M SMBflat-3L 46.78 mg 5000 Tape and reel Z0109MUF Z9M SMBflat-3L 46.78 mg 5000 Tape and reel 1. xx = sensitivity, y = voltage 5 Revision history T able 10. Document revision history Date Revision Changes Oct-2001 4 Last update. 10-Feb-2005 5 Package: TO-92 tape and reel delivery mode 5AL2 added. Table 4 on page 2: typo. mistake corrected 09-May-2005 6 1. (dV/dt)c instead of (dI/dt)c 2. V/µs unit instead of A/ms Reformatted to current standard. Table 2 on page 2: Typo 21-Apr-2006 7 corrected. Values for I split into two separate rows. GT Table 2: modified test conditions for (dV/dt) Changed “ambient” 10-Oct-2006 8 c. to “lead or tab” in Figure 2. 20-Oct-2010 9 Package: SOT-223 13” tape and reel added = 6AA4 Added package SMBflat-3L. Updated dimensions in Table6. 14-Dec-2010 10 Updated Figure3 and Figure12. Updated Table5: Product Selector. Doc ID 7474 Rev 10 11/12

Z01 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12 Doc ID 7474 Rev 10

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S TMicroelectronics: Z0109MN 5AA4 Z0109MA 1AA2 Z0109NN 5AA4 Z0103MA 1AA2 Z0103MN 5AA4 Z0103DA 1AA2 Z0103NA 1AA2 Z0107SN 5AA4 Z0107MN 5AA4 Z0107MA 1AA2 Z0107NN 5AA4 Z0110DN 5AA4 Z0110MN 5AA4 Z0110MA 1AA2 Z0107MA 2AL2 Z0103MA 2AL2 Z0107MA 5AL2 Z0103MA 5AL2 Z0107MN6AA4 Z0103MN 6AA4 Z0107NA 1AA2 Z0107NA 2AL2 Z0103NA 2AL2 Z0107NA 5AL2 Z0109MA 2AL2 Z0109MA 5AL2 Z0103MUF Z0107MUF Z0109MUF Z0103DN 5AA4 Z0103NA 5AL2 Z0109MN 6AA4 Z0103NN5AA4 Z0109NA 2AL2 Z0109SN 5AA4 Z0110SN 5AA4 Z0107DN 5AA4 Z0107DA 2AL2 Z0109DA 1AA2 Z0109DN 5AA4